Category: Pipes and fittings

This category covers all piping, connection and network products.

Subcategories

  • Pipes and fittings
    Pipes and fittings

    Creation and Repair of Piping Networks.

    In this category, you will find all the plumbing connection options available. Regardless of the type of network—whether copper, PEX, multilayer, steel, or even stainless steel this is where you can make your choice.

    Here are some tips for choosing the right products:

    Copper Piping:

    These dimensions are expressed in outer diameters and range from Ø6 to Ø108.

    Steel and Stainless Steel Piping:

    These dimensions are expressed in outer diameters, referred to as DN (Nominal Diameter), and range from Ø10.2 to Ø406.4 (larger DN sizes are available upon request).

    Threaded Fittings (regardless of material):

    These dimensions are expressed in inches (marked as: ").

    The inch, commonly known as "Gas Thread," is a measurement unit originating from England. The "British Standard Pipe" or "BSP" can be either parallel (BSPP) or tapered (BSPT).

    By default, unless otherwise specified, a male fitting will always be tapered (BSPT thread), and a female fitting will always be parallel (BSPP thread). In practice, this means that a male fitting will always screw into a female fitting. The seal is achieved on the thread using an appropriate sealing product such as Teflon tape or the various resins available on our site.

    A notable exception is flat-seal fittings. In this case, a gasket must be added to the sealing surface to ensure a tight connection without requiring thread sealing.

    Note that many fittings are considered "mixed" as they bridge the gap between threaded fittings and their respective categories.

    PEX and Multilayer Fittings

    These fittings are measured in outer diameters and range from Ø12 to Ø50. They require a sliding crimp tool (PEX only) or a radial crimp tool (PEX and multilayer).

    HDPE Fittings

    These dimensions are expressed in outer diameters and range from Ø16 to Ø75. They are only suitable for polyethylene pipes with white and blue bands.

    Don't forget! If you need advice, call us or send us a message—we will assist you as best as possible.

  • Vannes à sphère et prise en charge
    Vannes à sphère et prise en charge
  • Vannes à opercule
    Vannes à opercule
  • Robinets à papillons
    Robinets à papillons
  • Clapet et filtration
    Clapet et filtration
  • Brides - adaptateur - colliers
    Brides - adaptateur - colliers
    {hook h='CETemplate' id=13}
  • Hydrodistribution
    Hydrodistribution
  • Systèmes multicouches
    Systèmes multicouches
  • Flexibles de raccordement
    Flexibles de raccordement
  • Conduits inox
    Conduits inox
  • Cables chauffant autorégulant
    Cables chauffant autorégulant
  • Électrovannes
    Électrovannes

Pipes and fittings

In this category, you'll find all the possibilities plumbing has to offer in terms of connection and disconnection. Whatever the type of network, whether copper, PER, multi-layer, steel or even stainless steel, this is where you can make your water distribution choices.

Valves are equally important. You'll find all the standard valves for plumbing systems, such as ball valves, butterfly valves, gate valves and even a wide range of solenoid valves. Check valves, strainer valves and filters are also available here.

For larger networks, a wide range of flanges is available.

And don't forget! Whatever you need, if you can't find what you're looking for, give us a call or send us a message and we'll do our best to help.